2012-04-12 23:25 - last edited on 2012-04-13 7:10 by Kosh
TV-out is not working on my N8-00.. It did with Anna, but not since I've got Belle. When I set it to TV-out, my N8 sees my tv-out cable as headphones
Welcome to Nokia discussions board!
I advise you to reinstall the update from Nokia Suite.
If issue persists, perform a hard reset. First of all, back up your data using Nokia Suite. Then type *#7370# on your phone's keypad. The default lock code is 12345.
Alternatively, take your device to your local Nokia Care Point.
Let us know how you get on and feel free to post any other questions you may have.
No, it's not working! I re-installed Belle and did the hardreset-thing, but still the same problem.
I've seen a lot of discussions about this bug. Please try to fix it, guys! Because I used it a lot, before I installed Belle. I really don't want to go back to Anna, but if that's the only solution, maybe I have to.
I have the same problem with my nokia E6. TV Out does not work with belle. It worked fine with Anna but after update my tv out cable recognises as headset even tv out is set to default. Please help...
Have you tried installing Nokia Big Screen to see if it resets TV out.
I've recently updated to Belle and big screen is working well.
Although BigScreen is working well (I use it often) it only works via HDMI. I assume those members posting here do not have HD TV's, so are unable to connect via HDMI.
All the best.
Not sure what caused this to happen. But while we investigate the matter, you can try to use Nokia Play which lets you show photos and videos taken with your mobile wirelessly on your TV.
Let me know how you get on.
I too had same problem with my C6-01 (Belle). It was working fine in Anna.
Today I found the solution when I plugged the CA-75U to my internal TV tuner in my PC.
Then measured the resistance and found it to be 85 OHMs. Which is 180 OHMs in case of TV video IN.
Then disconnected the cable and tried in TV, but with a tweak.----
1. Plug the cable into phone.
2. Take a 100 OHMs resistor and connect it to the yellow port of your cable as shown in the attachment for 3 sec.
3. Then you can see the TV icon instead of the earphone icon in your phone.
4. Remove the resistor and connect the cable to the TV without disconnecting it from the phone and enjoy TV outing in Belle.
If the same worked or didnot worked for you please give a feedback.
I am confident that it will not make any temporary or permanent damage to your phone.
Still try at your own risk.
I didnot tried in other handsets.
Nokia working on this issue, they have already escalated this to our concern department and this is due to some bug in the software and this problem is observed in mass devices. nd gives the refresh for n8.............. yupiiiiiiiiiii
i think u r right. me agree with u. me also check with bt not 100ohm resister bit with headphone. before a weak i have insert a normal headphone not a headset to phone input headphone jack, and me see a tv sign like a 5800 is showing in n8 belle 0609 version, now today i have n8 1511 version with refresh belle, headphone jeck have 4pin point, ist Left vol 2nd Right vol 3rd TV out 4th Ground (Earth), so for tv support only 2pin works 3rd tv out nd 4th ground in Jeck. so u can try this trick who have wrote my Brother "nicozen" bcoz ots do not effect ur phone, do u know if ur particuler device headphones or f=headset or tv out cable ca-75u etc. insert in N8 jeck. phone does not direct connect vd them istly he checked if its not supported he says in screen.
so now if u r a belle user u can try atleast 10 time sure, with 100ohm resister. u do with ca-75u cable yellow pin just like "nicozen" user pic. insert the tv out jeck to phone then atach the 100ohm resister. or attach 100 ohm resisor istly to yellow pin then insert jeck. im realy sure ur device N8 tv out real work, if any one who have chalanged me than i will accept.
Dnt need Thnx. God Bless You.